por favor donde encuentro lista componentes para programador willem.ojo no el esquema que lo tengo.gracias

creo que son esto lo que quieres te pongo tambien lo que puede hacer pero yo no he podido programar ni leer todavia el 93c46 espero tengas tu mas suerte
Resistor 1/8w 5%
2k2 8
10k 7
100k 2
20k 1
1k2 or 2k2 2
220 1
15k 1
4k7 1
5R6 or 56 1
Resistor 1/4w 5% 0.5Ohm 1
Diode
1N4148 2
1N4001 6
Transister
BC547 or NPN type 3
BC557 or PNP type 2
IC CMOS logic
74HC(HCT)367 or 4503 or 40097 2
4015 3
4014 1
74HC04 or 4069 1
IC Supply
MC34063A or KA34063A 1
MC7805 (5V),LM7805,LM340T-5 1
Capacitor
100nF (0.1uF) 5
47uF/35V or 33uF/35V 1
470uF/25V 1
220pF 1
47uF/16V or 33uF/16V 2
DIPSW 12 POSITION 1
R-Pack 10K*8 (9pin) 1
LED 3
ZIF socket 32PIN 1
DB25 Male PCB 1
IC Sockets DIP
8 PIN 3
18 PIN 1
16 PIN 6
14 PIN 1
8 PIN 1
PIN HEADERS 1*40 1
MINI Jumper 2 PIN 6
Inductor 100uH -> 150uH 1
DC Jack 1
PIN HEADERS 40 pin [Cut to] 1
3 - 2pin 4 - 3pin 1 - 4pin 1 - 5pin 1 - 8pin


Supported:

Support CHIPS (EPROM,EEPROM,FLASH,I2C,PIC,MCS-51,AVR, 93Cxx, ISP)
EPROM 27C64, 27C128, 27C256, 27C512, 27C010, 27C020, 27C040,27C1001M27C1001, M27C2001, M27C400127C080 (A19) ,M27C8012716(Vpp25V),2732, (adapter DIP24) 2764, 27128, 27256, 27512, 27010, Vpp12.5V (21Vpp Modify Circuit)
EEPROM 28C65,28C64, 28C128, 28C256,28C512, 28C010, 28C020, 28C040M28C16A/17A (DIP28) (Adapter or Jumper) 28C16,XLS2816 (DIP24)
FLASH Memory 28F64, 28F128, 28F256, 28F512,28F010(MX28F1000), 28F020i28F001BX
Command seq. 555/AA,2AA/55,555/9029F64, 29F128, 29F256, 29F512,29F010, 29F020, 29F040
Serial (I2C) EEPROM24Cxx 24C02,24C04,24C08,24C16,--- page write ----24C32,24C64,24C128,24C256,24C512
Microwire EEPROM93Cxx <------ Data 8bit -----> (pin 6 ->ORG. [Schematic connect to GND])93C06, 93C46, 93LC46, 93C56, 93C57, 93C66, 93C76, 93C86 (8bit)<------Data 16bit------> (pin 6 ->NC [No Connect])93C06A ,93C46X,93C56,93C66,93C76,93C86 (NS)
MicroChip PIC 16C84, 16F84, 16F84A ,16F627/16F62812C508, 12C509, 12C508A, 12C509A,16C620, 16C621, 16C622---ICSP connector----16F870 -> 16F877
Atmel Flash Memory(Sector Programming) (Software Data Protection) AT29C256, AT29C512,AT29C010A, AT29C020, AT29C040,AT29C040AW29EE512,W29EE011, W29EE012, W29C020(128),W29C040 PH29EE010(W29EE011) ASD AE29F1008 (AT29C010), AE29F2008 (AT29C020) Ver. 0.992.66 up. Can run under win9x (disable prog. CPUIdle or CPUCool)
Atmel Flash MemoryAT49Fxxx (Subset 29Fxxx)(Byte-by-Byte Programming)(Software Data Protection) Command seq. 5555/AA, 2AAA/55, 5555/A0AT49F512, AT49F010,AT49F020,AT49F040, M29F002xSST39SF010,SST39F020,SST39SF040AT49F001,AT49F002 Command seq. 555/AA, 2AA/55, 555/A0Am29F512,Am29F010, Am29F020, Am29F040,29F002,29F002T,Pm29F002T
Serial Peripheral Interface (SPI)EEPROM Mode0 (0,0)AT25xxx, W95xxx [Atmel] AT25010,020, 040 (A8-A0) AT25080, 160, 320, 640, 128, 256 (A15-A0)[ST] W95010....256, Microchip 25x010 - 25x640--- Byte programming25010,25020,25040--- Page programming25C080,25C160,25C320,25C640,25C128,25C256,25C512AT25HP256,AT25HP512AT25HP1024 (24bit address)
Atmel EEPROM (page prog.) (Software Data Protection) AT28C256, AT28C010, AT28C040
Nonvaltile SRAM (DS12xx) DS1220,DS1225Y, DS1230Y/AB, DS1245Y/AB, DS1249Y/AB
static RAM (Test RAM) 6116, 6264, 62256, 62512, 628128
EPROM winbond,SSTElectrical Erase Chip W27E512, W27E010, W27C010SST27SF256, SST27SF512, SST27SF010, SST27SF020
Flash Memory SST,Sanyo SST28SF040A ,LE28F4001